【LVS】负载均衡集群

    LVS (Linux Virtual Server)是一种集群(Cluster)技术，采用IP负载均衡技术和基于内容请求分发技术。LVS可以实现LINUX平台下的简单负载均衡。

    其中LVS/NAT是一种最简单的方式，所有的RealServer只需要将自己的网关指向Director即可。

LVS负载均衡的NAT模式

一、实验准备

    在VMware Workstation虚拟机环境下，准备三台服务器，一台作为director, 两台作为real server。

二、网络配置

    director需要配置两块网卡，一块（eth0）与real server连接的内网，另外一块（eth1）连接到公网。

配置参考如下：

    director：eth0 192.168.20.28/24 （内网）

                    eth1 192.168.1.33/24 （外网）

    real server1：eth0 192.168.20.138

    real server2：eth0 192.168.20.250

    这三台服务器在192.168.20.0/24能互相通信

实现方法：

1、虚拟机网络模式选择【自定义VMnet1】，在这里的LVS-NAT实验中需要设置director的eth0和两台real server的eth0为自定义VMnet1模式，而director的eth1则设置为桥接模式，可以直接使用外网。

2、客户机Windows机器上VMnet1的IP设置，设置成与LVS的三台服务器eth0的IP在同一个网段，目的是为了能与三台LVS服务器通信，方便做试验

3、具体配置如下，real server1、2的网关均指向192.168.20.28

director：

real server1：

real server2：

三、LVS/NAT 配置

1、安装epel扩展源、nginx（测试用）（nginx在real server下安装）

wget http://mirrors.sohu.com/fedora-epel/6/i386/epel-release-6-8.noarch.rpm

[root@realserver1 ~]# yum -y install nginx

2、测试页面

[root@realserver1 ~]# echo "sr1-192.168.20.138" >/usr/share/nginx/html/index.html

[root@realserver2 ~]# echo "sr2-192.168.20.250" >/usr/share/nginx/html/index.html

3、Director 下安装ipvsadm

[root@director ~]# yum -y install ipvsadm

4、配置ipvsadm，创建/usr/local/sbin/lvs_nat.sh脚本

LVS的调度算法：轮叫调度(Round Robin)(简称rr) ,加权轮叫(Weighted Round Robin)(简称wrr),最少链接(least connection)(LC),加权最少链接(Weighted Least Connections)(WLC) 等

5、开启nat服务
[root@director ~]# sh /usr/local/sbin/lvs_nat.sh

6、测试LVS/NAT，由于sr1的权值为2，所以响应的请求为sr1的两倍

在windows下访问

LVS负载均衡的DR模式配置

[root@director ~]# ipvsadm -C
[root@director ~]# ipvsadm -ln
IP Virtual Server version 1.2.1 (size=4096)
Prot LocalAddress:Port Scheduler Flags
  -> RemoteAddress:Port           Forward Weight ActiveConn InActConn
[root@director ~]# iptables -t nat -F

一、网络配置

director：eth0

realserver1：eth0

realserver2：eth0

二、LVS/DR 配置

1、Director配置

[root@director ~]# vim /usr/local/sbin/lvs_dr.sh

执行脚本：
[root@director ~]# sh /usr/local/sbin/lvs_dr.sh 

2、在两台realserver配置

[root@realserver1 ~]# vim /usr/local/sbin/lvs_dr_rs.sh

#! /bin/bash
vip=192.168.1.200
ifconfig lo:0 $vip broadcast $vip netmask 255.255.255.255 up
route add -host $vip lo:0
echo "1" >/proc/sys/net/ipv4/conf/lo/arp_ignore
echo "2" >/proc/sys/net/ipv4/conf/lo/arp_announce
echo "1" >/proc/sys/net/ipv4/conf/all/arp_ignore
echo "2" >/proc/sys/net/ipv4/conf/all/arp_announce

执行脚本：

[root@realserver1 ~]# ifconfig lo:0
lo:0      Link encap:Local Loopback  
          inet addr:192.168.1.200  Mask:255.255.255.255
          UP LOOPBACK RUNNING  MTU:65536  Metric:1

[root@realserver2 ~]# ifconfig lo:0
lo:0      Link encap:Local Loopback  
          inet addr:192.168.1.200  Mask:255.255.255.255
          UP LOOPBACK RUNNING  MTU:16436  Metric:1

3、测试，在第四台机器上访问

[root@sh ~]# elinks 192.168.1.200

4、更改权值

[root@director ~]# vim /usr/local/sbin/lvs_dr.s

[root@director ~]# sh /usr/local/sbin/lvs_dr.sh

测试：

LVS结合Keepalived配置

两台director，两台realserver

[root@director ~]# ipvsadm -C

[root@director ~]# ifconfig eth0:0 down
[root@director network-scripts]# rm -rf ifcfg-eth0:0

一、安装keepalived

[root@director ~]# yum -y install keepalived

二、备用director

1、安装ipvsadm、keepalived

[root@sh ~]# yum -y install ipvsadm
[root@sh ~]# yum -y install keepalived

2、配置keepalived

[root@director ~]# vim /etc/keepalived/keepalived.conf

vrrp_instance VI_1 {
    state MASTER   #备用服务器上为 BACKUP
    interface eth0
    virtual_router_id 51
    priority 100  #备用服务器上为90
    advert_int 1
    authentication {
        auth_type PASS
        auth_pass 1111
    }
    virtual_ipaddress {
        192.168.1.200
    }
}

virtual_server 192.168.1.200 80 {
    delay_loop 6                  #(每隔10秒查询realserver状态)
    lb_algo rr                  #(lvs 算法)
    lb_kind DR                  #(Direct Route)
    persistence_timeout 0        #(同一IP的连接60秒内被分配到同一台realserver)
    protocol TCP                #(用TCP协议检查realserver状态)

    real_server 192.168.1.138 80 {
        weight 100               #(权重)
        TCP_CHECK {
        connect_timeout 10       #(10秒无响应超时)
        nb_get_retry 3
        delay_before_retry 3
        connect_port 80
        }
    }
    real_server 192.168.1.250 80 {
        weight 100
        TCP_CHECK {
        connect_timeout 10
        nb_get_retry 3
        delay_before_retry 3
        connect_port 80
        }
     }
}

3、备用director配置keepalived

scp到备用director

[root@director ~]# yum -y install openssh-clients
[root@director ~]# scp /etc/keepalived/keepalived.conf 192.168.1.218:/etc/keepalived/keepalived.conf

[root@sh ~]# vim /etc/keepalived/keepalived.conf

vrrp_instance VI_1 {
    state BACKUP   #备用服务器上为 BACKUP
    interface eth0
    virtual_router_id 51
    priority 99  #备用服务器上为90
    advert_int 1
    authentication {
        auth_type PASS
        auth_pass 1111
    }
    virtual_ipaddress {
        192.168.1.200
    }
}

virtual_server 192.168.1.200 80 {
    delay_loop 6                  #(每隔10秒查询realserver状态)
    lb_algo rr                  #(lvs 算法)
    lb_kind DR                  #(Direct Route)
    persistence_timeout 0        #(同一IP的连接60秒内被分配到同一台realserver)
    protocol TCP                #(用TCP协议检查realserver状态)

    real_server 192.168.1.138 80 {
        weight 100               #(权重)
        TCP_CHECK {
        connect_timeout 10       #(10秒无响应超时)
        nb_get_retry 3
        delay_before_retry 3
        connect_port 80
        }
    }
    real_server 192.168.1.250 80 {
        weight 100
        TCP_CHECK {
        connect_timeout 10
        nb_get_retry 3
        delay_before_retry 3
        connect_port 80
        }
     }
}

三、director启动keepalived

[root@director ~]# /etc/init.d/keepalived start      （主）
Starting keepalived:                                       [  OK  ]

[root@sh ~]# /etc/init.d/keepalived start                （从）
Starting keepalived:                                       [  OK  ]

查看ipvsadm状态

[root@director ~]# ipvsadm -ln
IP Virtual Server version 1.2.1 (size=4096)
Prot LocalAddress:Port Scheduler Flags
  -> RemoteAddress:Port           Forward Weight ActiveConn InActConn
TCP  192.168.1.200:80 rr
  -> 192.168.1.138:80             Route   100    0          7         
  -> 192.168.1.250:80             Route   100    0          16 

[root@director ~]# ip addr
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN 
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
    inet6 ::1/128 scope host 
       valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000
    link/ether 00:0c:29:92:99:4d brd ff:ff:ff:ff:ff:ff
    inet 192.168.1.28/24 brd 192.168.1.255 scope global eth0
    inet 192.168.1.200/32 scope global eth0
    inet6 fe80::20c:29ff:fe92:994d/64 scope link 
       valid_lft forever preferred_lft forever

四、两台realserver启动dr脚本/usr/local/sbin/lvs_dr_rs.sh 

[root@realserver1 ~]# sh /usr/local/sbin/lvs_dr_rs.sh 
[root@realserver2 ~]# sh /usr/local/sbin/lvs_dr_rs.sh 

五、测试，在第五台机器上访问vip192.168.1.200

nginx的负载均衡集群

清除之前的配置

[root@director ~]# ipvsadm -C
[root@director ~]# iptables -F
[root@director ~]# /etc/init.d/keepalived stop

[root@director ~]# yum -y install nginx

[root@director ~]# vim /etc/nginx/conf.d/lb.conf  //配置虚拟主机

upstream test {
    server 192.168.1.138:80;
    server 192.168.1.250:80;
}
     server {
            listen 80;
            server_name www.huangmingming.cn;

            location / {
                proxy_pass      http://test/;
                proxy_set_header Host   $host;
#                proxy_set_header X-Real-IP      $remote_addr;
#                proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for;
            }
        }

[root@director ~]# netstat -ntlp |grep nginx
tcp        0      0 0.0.0.0:80                  0.0.0.0:*                   LISTEN      11205/nginx   

测试：

[root@director ~]# curl -xlocalhost:80 www.huangmingming.cn
sr2-192.168.20.250
[root@director ~]# curl -xlocalhost:80 www.huangmingming.cn
sr1-192.168.20.138
[root@director ~]# curl -xlocalhost:80 www.huangmingming.cn
sr2-192.168.20.250
[root@director ~]# curl -xlocalhost:80 www.huangmingming.cn
sr1-192.168.20.138
[root@director ~]# curl -xlocalhost:80 www.huangmingming.cn
sr2-192.168.20.250
[root@director ~]# curl -xlocalhost:80 www.huangmingming.cn
sr1-192.168.20.138

设置权值

upstream test {
    server 192.168.1.138:80 weight=2;
    server 192.168.1.250:80 weight=1;
}

     server {
            listen 80;
            server_name www.huangmingming.cn;

            location / {
                proxy_pass      http://test/;
                proxy_set_header Host   $host;
#                proxy_set_header X-Real-IP      $remote_addr;
#                proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for;
            }
        }

[root@director ~]# curl -xlocalhost:80 www.huangmingming.cn
sr1-192.168.20.138
[root@director ~]# curl -xlocalhost:80 www.huangmingming.cn
sr2-192.168.20.250
[root@director ~]# curl -xlocalhost:80 www.huangmingming.cn
sr1-192.168.20.138
[root@director ~]# curl -xlocalhost:80 www.huangmingming.cn
sr1-192.168.20.138
[root@director ~]# curl -xlocalhost:80 www.huangmingming.cn
sr2-192.168.20.250

[root@realserver2 ~]# nginx -s stop

[root@director ~]# curl -xlocalhost:80 www.huangmingming.cn
sr1-192.168.20.138
[root@director ~]# curl -xlocalhost:80 www.huangmingming.cn
sr1-192.168.20.138
[root@director ~]# curl -xlocalhost:80 www.huangmingming.cn
sr1-192.168.20.138
[root@director ~]# curl -xlocalhost:80 www.huangmingming.cn
sr1-192.168.20.138
[root@director ~]# curl -xlocalhost:80 www.huangmingming.cn
sr1-192.168.20.138

[root@realserver2 ~]# nginx

[root@director ~]# curl -x192.168.1.28:80 www.huangmingming.cn
sr2-192.168.20.250
[root@director ~]# curl -x192.168.1.28:80 www.huangmingming.cn
sr1-192.168.20.138
[root@director ~]# curl -x192.168.1.28:80 www.huangmingming.cn
sr1-192.168.20.138
[root@director ~]# curl -x192.168.1.28:80 www.huangmingming.cn
sr2-192.168.20.250

本文转自 HMLinux 51CTO博客，原文链接:http://blog.51cto.com/7424593/1730693